Machine Operator Night Shift
Drake-Williams Steel, Inc.
Fabricate steel parts per drawings, operate machines and handle materials on night shift.
9 days ago ago
Junior (1-3 years)
Full Time
Omaha, NE
Onsite
Company Size
270 Employees
Service Specialisms
Steel Fabrication
Construction Services
Sector Specialisms
Commercial
Industrial
Healthcare
Institutional
Residential
Infrastructure
Role
What you would be doing
machine setup
steel fabrication
crane operation
forklift operation
quality inspection
mechanical maintenance
- Make adjustments to machine to ensure accurate dimensions as shown on the shop drawings.
- Crawl RARELY up to 10 feet to access tools, materials, etc.
- Reach overhead OCCASIONALLY to guide material attached to the cranes and to attach the chains from the crane to the material.
- Fabricate beams, tubes, angle, channel, bar grating, pipe, plate, or rounds according to the dimensions shown on cut lists and shop drawings, AISC code requirements for structural steel, and machine capabilities.
- Push material OCCASIONALLY into machine for fabrication. (SHEAR)
- Stand FREQUENTLY over the course of the 8 to 12 hour work shift.
- Operate forklifts, jib cranes, overhead cranes, conveyors, and transfers in order to move materials.
- Push and pull drawers open OCCASIONALLY to FREQUENTLY to retrieve tools. Employee will OCCASIONALLY push material attached to a jib crane or overhead crane to properly guide into place. Force varies up to 35 pounds.
- Climb OCCASIONALLY onto or over the conveyors.
- Lift weights up to 20 pounds from floor to chest CONTINUOUSLY, which includes the various tools utilized in the process of performing the usual work duties.
- Wear all required Personal Protective Equipment. PPE includes steel-toe safety shoes, hearing protection, safety glasses, gloves, and hard hats.
- Kneel in the commission of job duties OCCASIONALLY, depending upon the job.
- Sit only during the break and lunch periods. Rarely one will be able to sit while cutting material.
- Attend all meetings as required by management.
- Carry weights noted above distances ranging from a few feet to 60 foot.
- Fabricate material as trained and instructed.
- Stoop or crouch OCCASIONALLY while performing the regular job duties. The position will be held continuously for a few seconds to 15 minutes, depending upon the job.
- Identify cut list and shop drawing errors and discrepancies before or during early stages of fabrication.
- Reach forward OCCASIONALLY to perform job duties or to retrieve tools. The employee will OCCASIONALLY be required to reach to full forward extension.
- Walk OCCASIONALLY to FREQUENTLY over the course of the 8 to 12 hour work shift. The distances walked will range from a distance of a few feet to 60 foot.
- Perform minor mechanical tasks on machine (blade changes, cleaning, etc.)
- Identify steel shapes, sizes, and mill tolerances.
- Lift weights up to 60 pounds from floor to waist OCCASIONALLY during the work shift. Jib cranes and overhead cranes are available for the employees assistance with lifting.
What you bring
forklift
shop drawings
inventory
high school
6 months
communication
- Ability to use a computer for cut-lists and inventory purposes.
- Ability to operate forklifts and overhead cranes in a safe and proper manner. Use and understand industry and Drake-Williams Steel adopted hand signals used for crane operations.
- Exposure to heat, cold, wet and humid conditions in the shop area OCCASIONALLY.
- Ability to pass a Drake-Williams Steel administered test that covers shop drawing interpretation, fractional number calculations, basic geometry, etc.
- Visual ability to read and interpret shop drawings. Safety glasses are required in the shop area.
- Hear sufficiently to be aware of safety issues
- Ability to interpret, understand and utilize cutting lists, shop orders, and shop drawings.
- Ability to effectively communicate with co-workers, supervisors and managers.
- Ability to follow inventory procedures.
- Minimum of six months of experience in a steel manufacturing environment.
- Skill in using auto measurer, tape measure, or 1 rule.
- Ability to read, write, and perform higher arithmetic computations involving addition, subtraction, multiplication, and division of whole numbers, decimals and fractions.
- Ability to understand and carry out semi-complicated verbal and written instructions.
- Ability to multi-task.
- High School degree or equivalent.
- Lift weights up to 35 pounds from floor to waist FREQUENTLY during the 8 to 12 hour work shift
- Consistently and reliably works scheduled hours at assigned locations.
- Exposure to fumes, odors and dusts in the shop area OCCASIONALLY.
- Exposure to solvents, greases, oils, and coolants OCCASIONALLY.
- Ability to possess pride in own workmanship; demonstrate attention to detail, and work safely.
- Gross finger dexterity skills required to operate the various tools and equipment utilized in the course of standard job duties. Fine finger dexterity is not required.
- Ability to work under periodic supervision focused on the progress of work and setting priorities for job completion.
Information not given or found
Training + DevelopmentInformation not given or found
Interview process
Information not given or found
Visa SponsorshipInformation not given or found
Security clearanceInformation not given or found
People also searched
Rigger Jobs in Omaha United StatesMachinist Jobs in Omaha United StatesGeneral Operative Jobs in Omaha United StatesLaborer Jobs in Omaha United StatesForklift Driver Jobs in Omaha United StatesEquipment Operator Jobs in Omaha United StatesLabourer Jobs in Omaha United StatesMaterials Technician Jobs in Omaha United States
Company
Overview
Founded in 1882
Year Established
The company was established in Omaha as a steam-boiler maker.
1920s Innovation
Launched Omaha Buckets
They survived the Great Depression by introducing Omaha Buckets in the 1920s.
Pivoted in 1958
Shifted to Structural Steel
A significant pivot to structural steel manufacturing in 1958 expanded their capabilities.
260K sq. ft. Facilities
Fabrication Area Size
They operate over 260,000 square feet of fabrication space with advanced facilities.
- Survived the Great Depression by launching Omaha Buckets in the 1920s, then pivoted to structural steel in 1958.
- Evolved through four generations of family leadership into a world-class fabrication facility with plants in NE, IA, CO.
- Major projects range from institutional and healthcare buildings like TD Ameritrade HQ to rail components and bridges.
- The 2011 acquisition of Mountain Steel Division broadened capabilities and geographic presence into Colorado.
- Went employee-owned via ESOP in 2014, fueling modernization, robotic fabrication, and lean-manufacturing initiatives.
- Services cover structural, rebar, miscellaneous & railroad steel, coatings, detailing, distribution, and contract fabrication.
- Committed to delivering exceptional steel products and services to clients.
- Focused on continuous improvement, innovation, and operational excellence.
- Valuing integrity, transparency, and ethical conduct in all business practices.
- Dedicated to safety and well-being of employees, customers, and communities.
- Fostering a collaborative and inclusive work environment where every employee can thrive.
2040
Target Year for Net Zero Emissions
Aiming to achieve net zero carbon emissions by 2040.
- Committed to sustainability and minimizing environmental impact.
- Active implementation of recycling programs and energy-efficient practices in operations.
- Utilization of sustainable materials and techniques in manufacturing processes.
- Maintains certifications and complies with environmental regulations.
- Fosters a diverse workforce and promotes inclusive practices.
- Has a dedicated team working towards increasing workforce diversity in all departments.
- Aims to ensure equitable opportunities for all employees regardless of gender, race, or background.
Kablio AIIf you're someone who helps build and power the world (or dreams to), Kablio AI is your pocket-sized recruiter that gets you hired.
Copyright © 2025 Kablio